Finding the Best PPA Particles Supplier: A Comprehensive Guide for Businesses

Finding the Best PPA Particles Supplier: A Comprehensive Guide for Businesses

August 14,2024
In the world of advanced polymers and engineering materials, PPA particles (polyphthalamide) have emerged as a highly sought-after material, offering…
Lee mas
How to improve the toughness of transparent PP?

How to improve the toughness of transparent PP?

April 23,2024
Due to the relatively high rigidity of polypropylene molecular chains and a glass transition temperature around 0°C, how can the toughness of…
Lee mas
The Injection Molding Process of Polycarbonate (PC)

The Injection Molding Process of Polycarbonate (PC)

April 22,2024
PC, commonly known as polycarbonate, is colloquially referred to as bulletproof rubber due to its excellent mechanical properties. PC granules…
Lee mas
Global ABS Market Sales Set to Reach $38 Billion with 6% Annual Growth Rate

Global ABS Market Sales Set to Reach $38 Billion with 6% Annual Growth Rate

April 18,2024
The global ABS (Acrylonitrile Butadiene Styrene) market sales are projected to reach $38 billion by 2024, with a compound annual growth rate of 6.0%,…
Lee mas
Causes and Solutions for Defective Ejection in Injection Molded Products

Causes and Solutions for Defective Ejection in Injection Molded Products

April 17,2024
Adding fillers such as glass fibers and toughening agents to nylon can significantly enhance the mechanical properties of the material. However,…
Lee mas
Polyamide PA6 Injection Molding Process Conditions and Properties

Polyamide PA6 Injection Molding Process Conditions and Properties

April 16,2024
PA6 Polyamide 6 or Nylon 6？ Typical Applications: Due to its excellent mechanical strength and stiffness, it is widely used for structural…
Lee mas
Troubleshooting Surface Defects in TPE Injection-Molded Parts: Causes, Effects, and Solutions

Troubleshooting Surface Defects in TPE Injection-Molded Parts: Causes, Effects, and Solutions

April 15,2024
One of the reasons for surface issues in TPE injection-molded parts is the poor quality of raw materials TPE resin, as well as uneven dispersion of…
Lee mas
Why ABS Plastic Molded Products Crack

Why ABS Plastic Molded Products Crack

April 12,2024
The cracking issue of ABS resin molded products can be classified into the following three representative types based on visual inspection of the…
Lee mas
The Impact of Plastic Moisture Content on Injection Molded Parts

The Impact of Plastic Moisture Content on Injection Molded Parts

April 11,2024
The vaporization temperature of water is 100℃, and typically injection molding temperatures exceed 100℃. Water vaporizes at high temperatures,…
Lee mas
Addressing Shrinkage in Injection Molding: Strategies and Considerations

Addressing Shrinkage in Injection Molding: Strategies and Considerations

April 10,2024
Introduction: Shrinkage remains a persistent challenge in injection molding, often leading to defects and compromised product quality. In this…
Lee mas
The Future of Halogen-free Flame Retardant PA6, PA66

The Future of Halogen-free Flame Retardant PA6, PA66

April 09,2024
In recent years, with the increasing global environmental awareness, halogen-free flame retardant materials have been receiving more and more…
Lee mas
Thermoplastic Elastomers: Causes of Testing Deviation and Shore A to Shore D Conversion

Thermoplastic Elastomers: Causes of Testing Deviation and Shore A to Shore D Conversion

April 08,2024
Relative to other plastics, hardness is a more critical indicator for thermoplastic elastomers. Although hardness testing is relatively simple,…
Lee mas
Contáctenos
Name

Name can't be empty

* Email

Email can't be empty

Phone

Phone can't be empty

Company

Company can't be empty

* Message

Message can't be empty

Entregar
ETIQUETAS DE PRODUCTOS
ETIQUETAS DE PRODUCTOS